Pages

Monday, June 6, 2016

Turn Your Grill Into a Top-Notch Smoker!



The Trick That Turns Your Grill Into a Top-Notch Smoker

​It's called the snake method, and it's free!



They say that a great charcoal grill is just a so-so smoker. But do you really need to buy a $600 smoker to give your brisket the delectable flavor you seek? Weber's all-in-one chef, cookbook author, and food blogger Jamie Purviance says you don't have to splurge or hack apart your grill to make it a smoker. You just need to know the snake method.
"Innovations are happening in barbecue all the time," he says. "The snake method is one the more recent innovations, and it is just now going mainstream."

The method involves building a stacked wall of briquettes leaning against each other like dominoes in a semicircle. Light the charcoal on one end and let it burn like a fuse down the path of briquettes over the course of half a day. Snake method works on any circular charcoal grill, like the one you might have at home or the small one you take on camping grills. It'll hold a steady temperature all day and slow-cook ribs, brisket, pulled pork, fish, and whole turkeys and chickens. By dinner you'll have tender, fall-off-the-bone barbecue.
"It's good for meat that you want to smoke for several hours at low temperatures without having to add more charcoal," says Purviance. "It is not good for anything you want to grill over direct heat."
Be the first on your block to learn snake method by following these steps, courtesy of Purviance:

Use charcoal briquettes for the main body of the snake. Lay two rows of briquettes around the perimeter of half the charcoal grate (the lower grate), one row inside the other, making sure to neatly pack them against one other. Stack another layer atop each, so you end up with a semicircle two briquettes wide and two briquettes high. Because the snake is essentially a charcoal fuse, the longer you build it, the longer it'll burn. Now take four of five chunks of wood (for flavor) and stack them next to each other on top of one end of the Snake. Leave four or five inches of space from the very end before you place the first piece of wood.
Don't go for lighter fluid; if meat were supposed to taste like a parking garage smells, then people would marinate with this stuff. Instead, use a chimney starter. It looks like a Thermos with a wire rack inside. It's going to get hot, so find your insulated glove or mitt.
Fill the space under the rack with paraffin wax lighter cubes drop the rack in place, and put ten or so briquettes on top of it. Light the wax cubes, then watch for the briquettes to ash over and turn light gray. When they do, remove them with tongs and pile them atop the head of the Snake where you left space next to the wood. Now you've got a fire, even if it doesn't look like it. It's slow, but it's there.

Place a disposable foil water pan three-quarters full of water on the charcoal grate inside the semi-circle of the snake, as shown. "The water will help to keep the temperatures steady, and it will create a nice, moist environment for the meat to cook," Purviance says. Set the cooking grate in place over the charcoal grate, pan, and snake, and close the lid. Upper and lower vents control the airflow, and therefore the temperature, of the fire. Open the lower vent fully, and half-open the upper vent. Hang around until the temperature hits 250-300 degrees Fahrenheit.

Place the meat in the center of the cooking grate. Make sure none of it is directly above the Snake. Unlike hamburgers and thin cuts of meat that you cook directly over burning charcoal (direct grilling), you want to slow-smoke thick cuts of meat by placing them away from the charcoal (indirect grilling). Trying to cook a rack of ribs or a turkey like you would cook a steak turns it into a mess burnt on the outside and raw on the inside.

"The beauty of this method is you shouldn't have to do much adjusting," says Purviance. Check the thermometer every hour, and keep it between 250 and 300 degrees. Manage the fire as needed by opening vents to raise the temperature and closing them to lower it, but never close the vents completely. Leave the lid on as much as possible. Every time you open it for a look, you let all that perfectly heated air escape. If you need to extend the life of the fire, add unlit briquettes to the tail of the snake. 
"People ask me all the time, 'How long should I cook meat and when will I know it's done?'" Purviance says. For slow-cooked barbecue items, like pork ribs, tenderness is a better guide than temperature. For example, with ribs, the meat should tear when you push the tips of exposed, adjacent bones in opposite directions. The other way to check is with the bend (or bounce) test. Lift a rack at one end and let it bend (or bounce) in the air. If the meat in the middle tears open, it's done.

Monday, May 16, 2016

How to Build a French Cleat Shelf



How to Build a French Cleat Shelf to Hold Virtually Anything

French cleats are magical in their strength and simplicity. Here's how to make these amazing joints.


French cleats are often used to secure cabinets to walls, but can also be used to build modular shelves that can help organize your workspace. A French cleat system will be just as strong as most store bought wall organizers, and the hanging storage possibilities are only limited by your imagination and skill level.
To build this basic hanging system, start with 3/4-inch plywood and cut a strip that's 5 inches tall and at least 30 inches in length. This will be the section that attaches to your wall, and that the cleats hold onto. Of course, you can also cut the length of this strip to suit your needs but it should be long enough to be anchored into two wall studs that are typically 16 inches apart on center.
Make 45 Degree Cuts

Use a circular saw or jigsaw and adjust the shoe to a 45 degree angle. Use a guide or fence to keep the tool straight and cut along the length of the plywood.

Cut the Cleat for the Shelf


Use a shorter piece of plywood for the cleat that will be attached to the shelf. Make another 45 degree angled cut along the length of this piece, and line them up when you are finished to see how they will be attached.

Build Your Shelf


Attach two pieces of small plywood using wood screws to create your shelf and then attach the small cleat to the back of the shelf using wood glue and wood screws.

Secure Wall Cleat


Use a level and attach the long plywood cleat to the wall using wood screws. It's best to install the cleat into studs which are typically 16 inches to 24 inches apart.

Attach the Cleat to the Wall


Hang the shelf wherever you'd like along the length of the cleat.

Check the Cleat for Strength


If you can view a side profile of the French cleat, you should see the two angled pieces of plywood sitting flush against each other with the shelf flat against the wall cleat.

Start Using Your Cleats


We tested this French cleat connection and shelf using a 10 lb. accessories box filled with screws. The joint held up well, but for a shelf this size it's better suited to hold smaller individual tools.

Add Side Supports


You can reinforce the shelf by adding side supports which will help prevent items from falling off as well as provide additional strength when holding heavy items such as pipe clamps.

More Uses

Monday, May 2, 2016

Building Code Violations To Look Out For

Ducking Permits

You may think not applying for a building permit helps shave costs and sidesteps all the bureaucratic BS, and you'd be right—and wrong. Skipping permits means you won't have access to your local building inspector, somebody who knows all the codes and can ensure your project is in compliance. That translates to the utmost safety for you and your family, and avoids code violation stumbling blocks when it comes time to sell your house.
"By far the biggest mistake do-it-yourselfers make is not getting the right permits," says Rich Nolan, a structural engineer and owner of Nolan Engineering in Burt Hills, N.Y., a firm that specializes in home inspections. "You may think you can do without permits, but that can really come to haunt you in the end."
Want more motivation? Your insurance company may not cover your loss if it was due to improper installation or construction.

Improper Bathroom Venting

Got that new humidity-controlled venting fan all snugged up in the bathroom ceiling? Good job, but if your fan vents into an enclosed attic space, it's a code violation.
Dumping humid air into an enclosed attic can lead to mold growth and rotted wood. Codes say your fan should expel humid bathroom air to the outside via a 4-inch diameter vent pipe, typically the shortest route possible for maximum efficiency. A soffit vent is a good exit point.

Many Happy Handrail Returns

Whew! You got that new handrail on the stairs to the second-floor bedroom just in time for grandma's visit. But unless the ends of your wall-side handrail make a 90-degree turn and dead-end into the wall, you're violating code. Why? The open ends of a handrail can easily snag a purse strap or loose piece of clothing. Combine that goober with a set of stairs, and you've got a recipe for a hospital visit.

Bad Ledgering

Your accounting skills may be fine, but if your deck isn't properly attached to your house with a safe and secure ledger board, you could be putting your whole graduation party at risk. According to the North American Deck and Railing Association, some 40 million existing residential decks were built prior to 1990—before stricter codes for deck construction mandated safer techniques.
Ledgers are key points of deck failures. A ledger should be bolted or screwed directly to the house framing—not nailed—and must be protected with flashing to prevent moisture damage.

Wrong-Way Smoke Detection


The best protection you have in the event of a fire is a smoke detector. They're required on every floor of your house, inside every sleeping area, and outside every bedroom entry. Alarms on ceilings must be at least 4 inches away from walls, and alarms on walls must be 4 to 12 inches from the intersection of the wall and ceiling. For optimum performance, keep alarms at least 3 feet away from HVAC vents, ceiling fans, and lighting fixtures.
Smoke alarms in new construction must be hard wired and include battery backup, and multiple alarms must be wired together so that all alarms go off at the same time. If you're doing a renovation project on a house, you must update any battery-only alarms to meet the current requirements.